Danby Appliances Inc is a Montreal Quebec, Canadian-based company that was founded back in 1947. The company specializes in designing, manufacturing, and distributing appliances all over the local and international markets. Working with various retailers in Canada, the USA, Mexico, and the UK – they are able to offer the world what they have to offer.
Based in Guelph, Ontario and Findlay Ohio the company not only has a well-established name in Canada and other parts of the world. What was once a family-owned business, has now made its name as one of the best appliance businesses in the Americas. Generating more than 400 million dollars per year in sales alone, the company offers washing machines, air conditioners, microwaves, wine coolers, refrigerators, and other small appliances.
When facing an error code we suggest you grab a pen and paper to note down the code rather than pressing various buttons on your Danby portable AC. This way you will not risk damaging your appliance any further and will be able to find out the exact issue using the common error code list for Danby Portable AC Error codes listed below. Once you nail down the issue you can easily call in a professional, or fix the issue yourself.
Occasionally, a problem may arise that is minor in nature, and a service call may not be necessary. Use this troubleshooting guide for a possible solution.
Codes List
Error Codes | Problem |
---|---|
E1 | Error with the coils temperature sensor. |
E2 | Error with the indoor temperature sensor. |
E4 | Frost protection: the temperature of the coil is too low and the A/C shuts down to prevent excess frost build-up. When the temperature increases to 8°C (46.4°F), the protective setting is released and the previous setting is applied. |
Ft | Tank is full - Connect the drain hose and drain the collected water away. If error repeats, call for service. |
P1 | Bottom tray is full - Connect the drain hose and drain the collected water away. If error repeats, call for service. |
Lt | Low Temperature. The unit will defrost. The appliance will start again once defrosting is complete |
PF | Probe failure, call for service |
Troubleshooting
Problem: Unit does not start when pressing on/off button
Possible Cause:
- P1 appears in the display window
- Room temperature is lower than the set temperature. (Cooling mode)
Solution:
- Drain the water in the bottom tray.
- Reset the temperature.
Problem: Not cool enough
Possible Cause:
- The windows or doors in the room are not closed.
- There are heat sources inside the room.
- Exhaust air duct is not connected or blocked.
- Temperature setting is too high.
- Air filter is blocked by dust.
Solution:
- Make sure all the windows and doors are closed.
- Remove the heat sources if possible.
- Connect the duct and make sure it can function properly.
- Decrease the set temperature.
- Clean the air filter.
Problem: Noisy or vibration
Possible Cause: The ground is not level or not flat enough.
Solution: Place the unit on a flat, level ground if possible.
Problem: Gurgling sound
Possible Cause: The sound comes from the flowing of the refrigerant inside the air conditioner
Solution: It is normal
Problem: Power shut off at Heating mode
Possible Cause: The automatic over heat protection function. When the temperature at the air outlet exceeds 70°C/158°F, the device wi ll stop.
Solution: Switch on again after the unit has cooled down.
Remote Control
Parts and Control Panel
Manual Pdf
Portable Air Conditioner Manual
- Black and Decker AC Error Codes List and Fixes - November 1, 2024
- Pioneer AC Error Codes List and Solutions - November 1, 2024
- Rheem Pool Heat Pump Error Codes With Solutions - October 15, 2024
Hi there, I have a Danny portable that’s a week ole and randomly it shuts down and displays an error code PC 02
Did you get an answer to the flashing AP issue? Mine is doing the same thing
Hi, I took apart my portable AC to clean it out, now when I plug it back in I’m getting a E4 code and a red light at the power button. I can confirm that all parts on my AC unit are well above 8°c. It was sitting in the hot sun for about 6 hrs before I brought it inside.
My new AC keeps short cycling anybodyknow how to fix.
Since the day I purchased my heat/cool floor model the wifi has not worked. Hold the swing button for 3 seconds it will beep but AP has never come up on the display. Tried with the remote and the QR Code and still it does not connect. It is out of warranty now because if covid so I can’t even have it repaired. Any help would be appreciated. Unit works great otherwise. Very happy with its functionality.
Any idea why a Danby portable unit model 140HEAUBDB beeps 3 times right after it is plugged in and it won’t come on either from the control panel button or the remote button? The display powers on and shuts down after the 3 beeps. No error number on the display.
Hi Sergio
Did you ever find an answer to this issue? Mine is doing the same thing. Just tried to start it up after taking it out of storage (for the winter). Worked fine when it was put away.
I have the same unit and the same problem ~ did you get an resolution to your problem?
Also had this issue though it beeped more then three times. Ended up getting a replacement via warrantee