Westinghouse Electrical Corporation, commonly known as Westinghouse started back in 1886. Originally the company was called Westinghouse Electric and Manufacturing Company but was eventually renamed to match its workings in 1945. The name change was not the only change the company saw, as through the years it has been through several deals and transactions that changed its course and brought it to where it is today.
While the company may have exchanged hands every few years to decades, its range stood strong offering the world reliable air conditioners, freestanding dishwashers, and other household and commercial appliances. From its inception, the company has been focused on offering smart and friendly choices that offer you quick and easy solutions to your everyday problems. Such a product is its air conditioner system that helps you set the desired atmosphere in residential and commercial spaces.
Error codes are a common issue you may face with various appliances in your house or workplace. Rather than panicking, we suggest you grab a pen and paper and note down the code rather than pressing various buttons. This can commonly result in prolonging the issue or even causing more issues in the long run. So why risk damaging your appliance any further, when you will be able to find out the exact issue using the common error code list for Westinghouse air conditioner error codes listed below. Once you know the exact issue you can easily call in a professional, or fix the issue yourself.
Error signals on the display
Please read all of the instructions before using the air conditioner and keep this manual for future reference. The air conditioner you purchased has R410a gas refrigerant a environmental friendly gas which does not damage the ozone layer. In case of error, the display on the indoor unit shown the following error codes.
| Error Codes | Description of the trouble |
|---|---|
| E0 | Indoor unit EEPROM parameter error. |
| E1 | Indoor / outdoor units communication error. |
| E2 | Zero-crossing signal detection error. |
| E3 | Indoor fan speed has been out of control. |
| E4 | Open circuit or short circuit of indoor room temperature T1 sensor. |
| E5 | Open circuit or short circuit of evaporator coil temperature T2 sensor |
| EC | Refrigerant Leakage Detection |
| F1 | Open circuit or short circuit of outdoor ambient T4 temperature sensor |
| F2 | Open circuit or short circuit of condenser coil temperature T3 sensor |
| F3 | Open circuit or short circuit of compressor discharge T5 temperature sensor |
| F4 | Outdoor unit EEPROM parameter error |
| P0 | IPM malfunction or IGBT over-strong current protection |
| P1 | Over voltage or over low voltage protection |
| P2 | High temperature protection of compressor top diagnosis and solution |
| P4 | Inverter compressor drive error |
Remote Control
Troubleshooting
Malfunction: The appliance does not operate
Possible causes:
- Power failure/plug pulled out
- Damaged indoor/outdoor unit fan motor
- Faulty compressor thermomagnetic circuit breaker
- Faulty protective device or fuses.
- Loose connections or plug pulled out
- It sometimes stops operating to protect the appliance.
- Voltage higher or lower than the voltage range
- Active TIMER-ON function
- Damaged electronic control board
Malfunction: Strange odour
Possible causes: Dirty air filter
Malfunction: Noise of running water
Possible causes: Back flow of liquid in the refrigerant circulation
Malfunction: A fine mist comes from the air outlet
Possible causes: This occurs when the air in the room becomes very cold, for example in the COOLING or DEHUMIDIFYING/DRY modes.
Malfunction: A strange noise can be heard
Possible causes: This noise is made by the expansion or contraction of the front panel due to variations in temperature and does not indicate a problem.
Malfunction: Insufficient airflow
Possible causes:
- Unsuitable temperature setting.
- Obstructed air conditioner intakes and outlets.
- Dirty air filter.
- Fan speed set at minimum.
- Other sources of heat in the room.
- No refrigerant.
Malfunction: The appliance does not respond to commands
Possible causes:
- Remote control is not near enough to indoor unit.
- The batteries of remote control nearly has no power.
- Obstacles between remote control and signal receiver in indoor unit.
Malfunction: The display is off
Possible causes:
- Active LIGHT function
- Power failure
Malfunction: The display is off
Possible causes:
- Active LIGHT function
- Power failure
Malfunction: Switch off the air conditioner immediately and cut off the power supply in the event of:
Possible causes:
- Strange noises during operation.
- Faulty electronic control board
- Faulty fuses or switches.
- Spraying water or objects inside the appliance.
- Overheated cables or plugs.
- Very strong smells coming from the appliance.
Display and Parts
Manual
Split Type Room Air Conditioner Manual Pdf
- Aux AC Error Codes – How To Fix Them - November 15, 2024
- LG VRF Error Codes List – Multi V - November 15, 2024
- Black and Decker AC Error Codes List and Fixes - November 1, 2024
*If you can't find the code you're looking for on our site, please let us know, and we'll update our database as soon as possible.
My AC switching on off repeating ever 10 second automatically without remote control . What is the problem ???
You can help with Westinghouse Fault No. 64
WDS024westinghouse
A/C TYPE-duct split inverter
Refregirant-R410A
This unit showing on display E9
can you tell what is the issue
thanks.
Westinghouse split Air Conditioner Indoor unit model # wws36gh71 error showing
E1, E6, What is the problems
i have 36k Inverter with code E1….What that means??.
Error P4?