Whirlpool AC Error Codes List

Whirlpool Corporation is an American multinational manufacturer and marketer with headquarters in Benton Charter Township, Michigan, United States. The company came into being in 1911, and solely focuses on offering home appliances. Striving to be the best every step of the way the company made its way to the Fortune 500 companies in the world.

Employing more than 78,000 people in 70 manufacturing and technology research centers that are based in the top-rated cities in the world. While Whirlpool remains the parent brand, the company offers its appliances under a number of different brand names that make it the smallest of cities in the world.

There is a time in your life when the most reliable appliance you have starts to show an error. While it might be a dark day, fortunately for you there is a simple solution for most error codes. To help you out we have accumulated a complete list of the Whirlpool ac error codes. Offering you a chance to find out exactly what is wrong with your appliance, so you can finally make a decision. Rather than fighting with the appliance, or spending endless money on the repair, we suggest you first find the problem and then look for a solution.

Codes List

UA: Setting error, indoor and outdoor unit abnormal

E6: Communication malfunction

PL: DC input voltage is too low

PH: DC input voltage is too high

F0: Lack of Freon or block protection

P7: Temperature sensor malfunction of carbon fin

UU: DC overcurrent

P8: Overheat of carbon fin

F4: Break-circuit and short-circuit of outdoor condenser temperature sensor

F5: Break-circuit and short-circuit of outdoor discharge temperature sensor

E4: Discharge protection of compressor

F3: Outdoor ambient temperature sensor malfunction

U5: Current diction malfunction of complete unit

H7: Sync failure

EE: Storage slug

E1: Indoor PCB malfunction

E2: Anti-freezing protection

H4: Overload of system

H6: No motor of indoor unit feedback

F2: Indoor pipe temperature sensor malfunction

F1: Internal ambient temperature sensor malfunction

UF: Zero passage abnormal

H3: Overload of compressor

Lc: Startup failure

UH: No motor of outdoor unit feedback

E5: Overcurrent protection

U7: 4-way valve conversion abnormal

U1: Phase current detection malfunction of compressor

Troubleshooting

Error code is indicated: If error code such as;E2,E4,E5,E6,F1,F2,F3,F4,F5,H3,H4,H5,PL,PH appears on the indoor unit display, turn of the appliance and disconnect from power supply, then contact the nearest Whirlpool Authorized Service Center. (H1 and SE is not error code, H1 is the indicator of defrosting during heating, SE is the indicator of power save function.)

Before calling for service, try the suggestions below to see whether you can solve your problem without outside help.

ProblemSolution
The Air Conditioner Will Not StartThe air conditioner is unplugged. Make sure the power supply cord is plugged into a grounded 3 prong outlet.
The Air Conditioner Is Not Cooling ProperlyAirflow is restricted. Make sure there are no curtains, blinds, or furniture blocking the front of the air conditioner.
The Air Conditioner Is Freezing UpTurn off the unit and allow it to thaw until the ice has melted, then operate on a higher fan speed. If this continues to occur, contact customer service for additional help.
The Remote Control Is Not WorkingBatteries are inserted incorrectly. Check that the batteries are inserted in the correct direction.
Water Is Dripping From the Unit on the Outdoor SideThe weather is hot and humid. This is normal during periods of high humidity. NOTE: Do not drill a hole into the bottom of the metal base pan; doing so will reduce cooling performance.
Water Is Dripping Inside the RoomThe air conditioner is not properly leveled. The air conditioner should slope slightly downward toward the outside. Level the air conditioner to provide a downward slope toward the outside to ensure proper drainage.
Water Collects in the Base PanMoisture removed from the air is collecting in the base pan. This is normal. Water that collects in the base pan will evaporate to the outside air. This helps with the unit's cooling process.

NOTE: Do not drill a hole into the bottom of the metal base pan; doing so will reduce cooling performance.

Remote Controls

Remote Control
Remote Control
Remote Control
Remote Control Symbols

Manual Pdf

Whirlpool Air Conditioner Manual

Windows AC Use and Care Guide

Danny Reese
Latest posts by Danny Reese (see all)


*If you can't find the code you're looking for on our site, please let us know, and we'll update our database as soon as possible.

24 thoughts on “Whirlpool AC Error Codes List”

  1. Sometimes it display ER on screen and that time ac isn’t working. When I switch off the power button for 4-5 hours then it work but for this also I have to try 4-5 times.

    Reply

Leave a Comment