Electrolux AB is a Swedish multinational home appliance manufacturer that is based in Stockholm. Currently ranked as the world’s second-largest appliance manufacturer by units sold, waiting patiently in line after Whirlpool. Today, Electrolux sells its appliances under various names, including its own. Allowing them a chance to dominate a good chunk of the world without using its original name.
To help you out we have listed down the most common error codes of Electrolux Air Conditioner.
Codes List
Error Codes | Meaning |
---|---|
E2 | Anti-freezing protection |
E3 | System block or refrigerant leakage |
E4 | Compressor exhaust high temperature protection |
E5 | AC over-current protection |
E6 | Communication failure between indoor unit and outdoor unit |
E8 | Anti-high temperature protection |
H4 | Anti-high temperature protection |
H6 | No feedback of indoor fan motor |
C5 | Jumper cap malfunction protection |
LP | Indoor unit and outdoor unit doesn't match |
L3 | Outdoor DC fan motor malfunction |
L9 | Power protection |
Fo | Gathering refrigerant |
F1 | Indoor ambient sensor open or short circuit |
F2 | Indoor tube sensor open or short circuit |
F3 | Outdoor ambient sensor open or short circuit |
F4 | Outdoor tube sensor open or short circuit |
F5 | Exhaust sensor open or short circuit |
F6 | Overload limit / drop frequency |
F8 | Over current limit / drop frequency |
F9 | High exhaust temperature limit / drop frequency |
FH | Anti-freezing limit / drop frequency |
H1 | Defrosting |
H3 | Compressor overload protection |
H5 | IPM protection |
HC | PFC protection |
EE | Loading EEPROM malfunction |
PH | High PN voltage protection |
PL | Low PN voltage protection |
U7 | 4-way valve reversal abnormal |
P0 | Compressor Min frequence in test state |
P1 | Compressor rated frequence in test state |
P2 | Compressor maximum frequence in test state |
P3 | Compressor intermediate frequence in test state |
LU | Frequency limiting (power) |
EU | Frequency limiting (module temperature ) |
Remote Control
Troubleshooting
Problem | Solution |
---|---|
Poor Equipment performance | The air outlet or inlet in the exterior part is obstructed. |
The temperature in the exterior is high due to direct sunlight or another heat source. | |
Heater or a cooking stove is being used in the same room. | |
Room is full of people. | |
The air filter is obstructed by dust or is dirty. | |
Inappropriate temperature adjustment. | |
Front part is obstructed. | |
The capacity of the equipment is not adequate for the size of the room. | |
Air conditioner was just turn on. | |
Windows or doors are open. | |
Motor protector has been activated. | |
The unit does not start | The plug is not connected to the outlet. |
No electricity in the outlet. | |
The voltage is different. | |
Temperature is not adjusted properly. | |
Burned fuse. | |
The remote control batteries need to be replaced. | |
Wrong operation time. |
Remote Control Display
- Open and lift the front panel up to an angle until it remains fixed with a clicking sound.
- One press of the manual control button will lead to the forced AUTO operation.
- Close the panel firmly to its original position.
Indoor Display Panel
Solutions For Problems
If your air conditioner malfunctions, check the following information to find solutions or probable causes of the failure. Do not try to repair the unit by yourself, if these solutions do not solve the failures; call your local service repair team.
Problem | Solution |
---|---|
Poor Equipment performance | The air outlet or inlet in the exterior part is obstructed. |
The temperature in the exterior is high due to direct sunlight or another heat source. | |
Heater or a cooking stove is being used in the same room. | |
Room is full of people. | |
The air filter is obstructed by dust or is dirty. | |
Inappropriate temperature adjustment. | |
Front part is obstructed. | |
The capacity of the equipment is not adequate for the size of the room. | |
Air conditioner was just turn on. | |
Windows or doors are open. | |
Motor protector has been activated. | |
The unit does not start | The plug is not connected to the outlet. |
No electricity in the outlet. | |
The voltage is different. | |
Temperature is not adjusted properly. | |
Burned fuse. | |
The remote control batteries need to be replaced. | |
Wrong operation time. |
Outdoor Led Description
Manual
Latest posts by Danny Reese (see all)
- Aux AC Error Codes – How To Fix Them - November 15, 2024
- LG VRF Error Codes List – Multi V - November 15, 2024
- Black and Decker AC Error Codes List and Fixes - November 1, 2024